Leading 10 common forklift accidents ， forklift operation should pay attention to these issues ！.
Leading 10 common forklift accidents ， forklift operation should pay attention to these issues ！.
Blog Article
Do not undervalue the forklift at work. If the operation is not good, there will be major mishaps in mins, and there are lots of crashes entailing forklifts.
Instance 1: The forklift freight obstructed the driver's view, and the individual ahead can not be located, causing a moving mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy goods, the employees utilized their body weight as the weight, which virtually created casualties.
Situation 3: The size of the forklift freight surpasses the allowable width of the course and holds on the roadside rack, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift operation should pay attention to these issues ：.
Begin.
1. Prior to starting, observe the surroundings, and after validating that there are no obstacles that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be risk-free before beginning.
3. When the forklift begins with a tons, the driver must first verify that the lots is steady and dependable.
4. The beginning should be slow-moving and steady.
Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast must be slanted backward. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles in the sky. When the tons is taking a trip, the fork should not be elevated expensive, which will impact the security of the forklift. .
3. After unloading, the fork ought to be decreased to the regular driving position before driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal ought to be released initially. High-speed doglegs are forbidden. High-speed sharp turns will trigger the lorry to shed side stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it has to comply with the traffic rules in the factory and must keep a certain security distance from the car in front. .
7. When the forklift is running, the tons needs to be in the lowest setting that does not impede the driving, and the gantry ought to be appropriately tilted back. The tons shall not be raised except when stacking or loading. .
8. The elevation of the lots have to not obstruct the motorist's view. In special situations, when the item affects the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to base on the fork to hold products and play a balancing duty. .
12. If issues are found, they will be fixed and reported in a timely manner, and they will certainly never operate with ailments or conceal them.
loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the lots of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a solitary fork or utilize a fork top or pull. In unique situations, safety and security warning signs must be established to remind bordering pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be stopped with the brake. .
4. The speed of the vehicle must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork pointer should not touch various other items or items. The lots should be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted forward somewhat when the lots is decreased to allow for simple positioning of the load and extraction of the forks. .
6. It is prohibited to fork items at high speed and collide with difficult things with the fork head. .
7. When the forklift is working, it is forbidden Electric Forklift Truck for Warehouse for people to stand around the fork, so as to stay clear of the collapse of the goods and injure people. .
8. Overloading is Electric Forklift Truck for Warehouse forbidden, and it is banned to use forks to lift personnel to participate in high-altitude procedures to stay clear of high-altitude dropping crashes. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to choose, transform pallet dump.
Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake handle to dead or depress the parking brake switch.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the key. .
Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubing oil and cooling water ought to be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the outside leakage should additionally be inspected and the seals ought to be replaced in time.
Forklift Safety Operation Specifications.
1. You have to inspect before leaving the car;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and uniform, and no switching on the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the car should be driven backwards when worsening;.
8. When the forklift workers carry the goods and move on, if they experience huge or heavy products and most likely to the chauffeur's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to utilize stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following problems.
1. Contours, slim roadways, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the area with the same length as the obstacle ought to be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844